Maple Grove Woodworks » woodworking business

Workshop Design #4

Dennis_MGWW — Thu, 24 Sep 2009 15:54:46 +0000

Front View (Click for larger view)

Here is a quick update of where I am on the workshop design. If you remember from my first article, the footings and frost wall already exist so I cannot modify anything with them, but every thing else is fair game.

I am not quite as far along as I had hoped to be at this point with the design, but here is what I have so far. As you can see from the pictures, I have the wall studs up on 3 of the sides. I have to research the rough opening sizes I’ll need for the doors before doing the fourth wall.

I also have one of roof trusses drawn. Actually, I haven’t decided if they will be premade trusses or if I will just build them on site. You can now see what I mean by a center aisle horse barn. The difference here is that my workshop will not be raised on the interior, the raised section will house the second floor.

Iso View (Click for larger view)

The next step will be to finish the front walls and the rest of the roof trusses. Then I will start adding the sheeting on the outsides of the walls and drywall on the inside of the walls.

Mary Kay Give Away Display

Dennis_MGWW — Tue, 22 Sep 2009 16:20:48 +0000

Mary Kay Give Away Display

A couple of years ago, I had a client who sold Mary Kay cosmetics. She wanted me to build her a display that she could place near the cash registers at local businesses. People could fill out an entry form and place it inside the display in order to win prizes.

She wanted the display to be a little nicer and have more class than the usual cardboard box or fish bowl that you normally see for these types of things. She also did not want it to have a very large footprint. Business owners would be more likely to let her place it on their counter if it didn’t take up too much room. It also couldn’t be too small or else it wouldn’t be noticeable.

The display also needed to have some sort of “back” to it so that a pad of entry forms could hang from it. Above the entry pads, their had to be enough room for a sign explaining what the entry forms were for.

I decided that even though this project was not going to be a very large one, I really needed to go through the entire design process. The design needed to be more than just a rough sketch before I started building it.

Cad Design

The first thing I did was to make a prototype out of some cardboard. This was just to determine the overall size of the display. I wanted to get a good visual of the size to show my client. I ended up making a couple of different sizes to present. This part of the process really only took about 1/2 an hour. I basically cut up a few pieces of cardboard and taped them together to form a box for the different sizes. I also mocked up the “back” with some cardboard as well.

Once this was done, I began modeling the design in my CAD software. This allowed me to get all of the joints figured out, as well as give a nice visual representation of the style for my client. Between the cardboard mock-ups and the 3 dimensional CAD design, I felt that I had enough to show the client and see if she wanted to move forward from there.

Display Closeup

From the very beginning, I had a certain image in my head as to what the box should look like. I didn’t consciously design it with an Asian flair, but that is how it turned out. The curved legs, and curved edging of the top accomplish this. I also wanted to add some marquetry to it as well. I decided on a very simple rose pattern for the front of the box.

I have always liked the contrast between walnut and maple and decided to use them on this project. In this case, I would use some curly maple that I had left over from another project. I would also use purple-heart and cherry on the rose.

Rear View

My client loved the size and design that I had come up with, and gave her approval for going ahead with the project. It was at this point that I decided I would need some jigs and patterns made up so that I would be able to make several of these. In order to come up with the jigs and patterns, I built a prototype of the box out of MDF and pine.

The prototype allowed be to work out some of the challenges of creating some of the curved pieces and the joinery. The legs of the piece are curved on two faces, not just tapered. Once the prototype was complete, I began making boxes.

Workshop Design #2

Dennis_MGWW — Tue, 15 Sep 2009 11:00:28 +0000

Before I get into the nitty gritty of the workshop design, I need to pause and make list of what features I really want my workshop to have. This will start out as a “wish list”, but I am sure I will have to pare it down later on due to cost. I figure that if I design it the way I would really want it, I can always add some of the items later on down the road if I can’t afford them right away.

The first thing I want to consider is the overall style of the building. I live out in the country surrounded by farms and fields. I have always liked the look of old center aisle horse barns and that is what I would like my shop to resemble. Plus, the design gives me the opportunity to have a small second floor where I can have either an office or extra storage. The horse barn look is both aesthetically pleasing to its surroundings and very practical for use as a workshop.

Ceiling height would be my next consideration. I would like a minimum of 10ft high ceilings. This makes it easy to stand 4×8 sheets of plywood on end and if needed roll it on its corner and still have a foot to spare. The diagonal measurement of a 4×8 sheet is just shy of 9ft.

I will probably stick with 10ft high ceilings for a couple of reasons, both related to cost. I figure that it will cost roughly 20% more in materials for the walls by going to a 12 ft ceiling. Also, when it comes to heating and cooling, it will be less expensive with the 10ft ceilings. One other thing, I think the building would just look too tall with a 12 ft ceiling.

The building will certainly have to be insulated. I live in Michigan where the winters are cold and the summers are hot. I will probably install a propane furnace, the kind that hangs from the ceiling, to heat the shop during the winter. I have yet to research all of the different kinds of furnaces but as soon as I do I will post an article dedicated to it.

Another luxury would be to have 6 inch wide walls rather than the typical 4 inch. The purpose of this would be to have thicker insulation in the walls which will reduce the heating and cooling costs. However, I am pretty sure the cost of 2×6 wall studs may be a bit higher than I am willing to pay.

Windows are another thing to consider, and there will certainly be some trade offs with them. I want as much natural light as possible coming into the shop, but I don’t want to sacrifice too much wall space either. I imagine I will have 2 windows on the side walls and 1 window on each end wall both downstairs and upstairs giving me a total of eight windows.

Both the large overhead door and the entry door will be insulated. The overhead door is for easy loading and unload of lumber and projects. I do not ever intend on driving into the shop. Because I don’t ever intend on driving into the shop, I plan on making the poured cement floor as flat as humanly possible. At this point, I can see no reason to put a drain in the floor, so there is no need to slope the floor.

The shop will have to have both 110 and 220 outlets. I currently only have 1 machine that runs on 220, but I plan on having a couple more someday.

At this point, this pretty much makes up my requirements list for the overall construction of the workshop. I will discuss some of my requirements for the interior of the shop in my next article.

Workshop Design #1

Dennis_MGWW — Thu, 10 Sep 2009 16:10:24 +0000

When I first start woodworking, my wife and I lived in a two story house with a very small detached garage. The garage was actually not very suitable for a workshop, at least not without a lot more work than I was willing to put into it. Besides that, I didn’t want that much money sitting in the garage in that particular neighborhood. Therefore my workshop was in the unfinished basement of the house. It would have made Matt proud.

This worked out well until we decided to move. In 2004 we built a new house out in the country. The new house had an attached garage which was large enough for a small workshop and both cars. I decided, though, that I would like a dedicated building for a workshop that was the same size as the garage.

So when the concrete was being poured for the basement of the house and garage, I also had the footings and frost wall poured for the workshop. At that point we finished the house and garage, but due to financial reasons the workshop was left as is… just a short cement wall sticking out of the sand. My kids have had a great time playing in what I call “the most expensive sandbox around”.

I am now planning on building the rest of the shop next summer. So I though I would start the design process, and have everything planned out before construction begins.

Workshop Floor

The outside dimensions of the frost wall are 24ft by 32ft, giving me just under 768square feet of floor space. As the design progresses I will update the the blog with new images of the design. so far, all I have drawn are the footings, frost wall, and the cement floor (in the image the green represents a little grass around the outside).

As you can see there is a break in the wall for a large garage door and an entry door. The next step will be to start throwing some lumber at it and constructing some walls.

About the Maple Grove Woodworks blog

Dennis_MGWW — Wed, 26 Aug 2009 17:28:20 +0000

Welcome to the Maple Grove Woodworks blog. Maple Grove Woodworks is my own personal woodworking business. Being a professional woodworker has long been a dream of mine. I am not quite 100% there yet, as I still have my day job.

My day job actually helps my woodowrking business. I use a Computer Aided Design (CAD) workstation to design tools for the plastic injection molding industry. I have been able to design projects on my CAD workstation during lunch hours, or coming into work early. This has been a huge help when figuring out complicated joints.

The CAD software I use is called Unigraphics. It is quite a high end piece of software. I don’t know for certain, but I think it is around $20,000 for a single license. It is not something I would buy for a small single man woodshop. But as long as I can use it for free it works great.

The initial purpose of this blog (I say initial because the purpose may change as the site evolves) is to document how I design and build my projects as well as a showcase for them. Feel free to make comments or ask questions about any of my postings. I hope to learn as much as I can from the woodworking community at large and help anyone else on their woodworking journey as well.